Uxcell a11032500ux0133 KSD9700 NC 45C Bimetal Thermostat Temperature Switch Pack of 2

#ad
Dragonmarts - BISS a11032500ux0133 #ad - Active temperature: 45 5 °c; reset temperature: >=30 °c; color: black, silver tone. Product name: temperature control switch; material: plastic, bimetal; model: Ksd9700 . The bimetal disc is in free state and the contacts are closed when the electrical appliance is working in normal condition. When the ambient temperature raises to the preset operating temperature, the contacts open as the Bimetal disc deforms to jump when being heated, then the circuit is cut off to control the temperature.

Then the contacts will close automatically to cut on the circuit when the electrical appliance is cooled down to the reset temperature. Widely used in home appliance and rsquo; use motor and electrical equipment, such as air Conditioner motor, thermal appliances, transformer, etc. Type: ncnormal close; contact capacity: 250V 5A; max rated disconnection temperature: 45C/113F.

Uxcell a11032500ux0133 KSD9700 NC 45C Bimetal Thermostat Temperature Switch Pack of 2 #ad - Ul>ksd9700 product is a kind of thermostat which adopt the Bimetal disc as the temperature sensing element.

#ad



Carbon Heater Tape 17 ft Length x 0.59 in Width

#ad
CarbonHeater CT15 #ad - You can make your own inexpensive heated gloves, sleeping bag, vest, heated pad, jacket, heated insoles, socks. You can cut it by the length to increase the power. Length: 17 ft. But you can cut it into smaller length only. Diy carbon heater tape for vest, jacket, insoles, gloves. It's a resistive carbon heating tape.

You must have an experiance in electronic DIY projects to prevent any hazardous of using it. The power consumption of 1 meter is about: 07w/m 3. 7v, 2. 9w/m 7. 4v, 7. 5w/m 12V. It cannot be cut into smaller widths. 5±1g/m. 1, 5k. Width: 059 in 5 meters x 15±2mm x 0, 6±0, 1 mm. 19±1 ohm/m. Idial for DIY heating clothes.

#ad



MG Chemicals 8331 Silver Epoxy Adhesive - High Conductivity, 10 min Working time, 14 g, 2 Dispeners

#ad
MG Chemicals 8331-14G #ad - It is rohs restriction of hazardous Substances and REACH Registration, Evaluation, Authorization of Chemicals compliant. Specificationscontinuous service temperature range-67 to +302 degrees FWork time10 minutes dependent on temperatureTime until fully cured5 hours at 77 degrees FColorSilver grayThermal conductivity0

903 w/m•k at 25 degrees c per aSTM E 1461Electrical resistivity00174 ohms-cm after 25 degrees C full cure per method 5011. 5 in mil-std-883hmix ratio by volume1:1MG Chemicals manufactures chemical products for the electronics industry. Two-part silver-filled epoxy adhesive with good conductivity and faster working time than MG Chemicals 8331S adhesive to bond electronic devices, form conductivity seals, and cold solder heat-sensitive materials.

MG Chemicals 8331 Silver Epoxy Adhesive - High Conductivity, 10 min Working time, 14 g, 2 Dispeners #ad - Easy 1:1 mix ratio. The mg chemicals 8331 is a two-part silver-filled epoxy adhesive with good conductivity and a faster working time than MG Chemicals 8331S adhesive to bond electronic devices, form conductivity seals, and cold solder heat-sensitive materials. The company, bc, founded in 1955 and headquartered in Surrey, Canada, meets International Organization for Standardization ISO standard 9001.

What's in the box?14 g of 8331 silver conductive epoxy adhesive in two syringes 7-g syringe of part A and 7-g syringe of part B Diy carbon heater tape for vest, jacket, insoles, gloves. Electrical resistivity: 0007 Ω·cm, thermal conductivity: 1.

#ad



Carbon heater tape 17 ft length x 0.59 in width

#ad
CarbonHeater CT15 #ad - You can make your own inexpensive heated gloves, heated insoles, sleeping bag, jacket, vest, heated pad, socks. You can cut it by the length to increase the power. Continuous service temperature range from -55 to 150°C -67 to +302°F. You must have an experiance in electronic DIY projects to prevent any hazardous of using it.

It's a resistive carbon heating tape. Stores and ships at room temperature, no freezing or dry ice required. Easy 1:1 mix ratio. 5±1g/m. The power consumption of 1 meter is about: 07w/m 3. 7v, 2. 9w/m 7. 4v, 7. 5w/m 12V. It cannot be cut into smaller widths. Diy carbon heater tape for vest, jacket, insoles, gloves. Electrical resistivity: 0

Carbon heater tape 17 ft length x 0.59 in width #ad - 007 Ω·cm, thermal conductivity: 1. 4 w/m·K. Diy carbon heater tape for vest, insoles, jacket, gloves.

#ad



GENNEL 10gram Thermal Conductive Glue Silicone Plaster Viscous Adhesive Cooling Compound For LED GPU Chipset Heatsink

#ad
GENNEL GENNEL G109 #ad - 100% new Heatsink plaster. Application: apply to all heatsinkf no fixed clip thermal paste. Features: thermal properties, strong adhesion * Melting capacity: 0 200 ℃ / 24Hours * Evaporation: 0001% 200 ℃ / 24hours * thermal conductivity:> 1. 2w/m-k * thermal Impedance: 5. 1 * dissipation coefficient.

Idea for mosfet heatsink,vGA CARD Northbridge Southbridge Heatsink.

#ad



BNTECHGO 22 Gauge Silicone wire 10 ft red and 10 ft black Flexible 22 AWG Stranded Copper Wire

#ad
bntechgo.com #ad - Provides work time of 10 minutes and has full cure time of 5 hours at 77 degrees F. 10gram Tube. Diy carbon heater tape for vest, insoles, jacket, gloves. Gennel g109. Two-part silver-filled epoxy adhesive with good conductivity and faster working time than MG Chemicals 8331S adhesive to bond electronic devices, form conductivity seals, and cold solder heat-sensitive materials.

High strand count copper core, 22 awg silicone stranded wire has 60 strands 008 mm tinned copper wire, the copper strands are tinned, protecting them from corrosion and making it easier to solder. They are constructed with premium silicone rubber insulation. High temperature resistance 200 degree C, Low temperature resistance, in extreme cold -60 degree C.

BNTECHGO 22 Gauge Silicone wire 10 ft red and 10 ft black Flexible 22 AWG Stranded Copper Wire #ad - Rated voltage: 600 volts. Outside diameter 1. 7 mm, tolerance +/- 01 mm. 22 gauge silicone wire kit: 2 colors, red and black, each color 10 ft, total 20 feet. Bntechgo silicone wire are widely used for model planes, model cars, household appliances, meters, lamps, batteries, model ships, instruments, electric heating appliances, motor lead wire and digital fields.

Continuous service temperature range from -55 to 150°C -67 to +302°F.

#ad



Low Cost, 1 Part Heat Dry Electrically Conductive, Silver Epoxy Adhesive AA-DUCT AD1 , 2.5gm Syringe

#ad
Atom Adhesives #ad - Aa-duct ad1 designed for use in diversified applications as microwave EMI & RFI shielding, in the assembly or repair of printed circuit boards, wave-guides, static shielding, electronic modules, flat cable, connections, and circuitry. Perfect for led GPU Chipset Heatsink. Two-part silver-filled epoxy adhesive with good conductivity and faster working time than MG Chemicals 8331S adhesive to bond electronic devices, form conductivity seals, and cold solder heat-sensitive materials.

Appearance Silver, Cure Type Heat cure. Availability: This epoxy can be supplied in various different packages. Aa-duct ad1 shows slight settling when stored for a long period of time, no caking and will re disperse to a smooth homogeneous state. Diy carbon heater tape for vest, jacket, insoles, gloves. Electrical resistivity: 0

Low Cost, 1 Part Heat Dry Electrically Conductive, Silver Epoxy Adhesive AA-DUCT AD1 , 2.5gm Syringe #ad - 007 Ω·cm, thermal conductivity: 1. 4 w/m·K. The following precautions should be exercised Use with adequate ventilation. Avoid prolonged contact with skin, if contact with skin occurs, wash area immediately with a soap and water avoid prolonged breathing of vapor. Dangerous if swallowed. High strand count copper core, 22 awg silicone stranded wire has 60 strands 0

#ad



uxcell KSD9700 Thermostat, 45℃ Normally Open Temperature Switch Thermal Switch, N.O 5A Metal Bimetal Temperature Controller 2pcs

#ad
uxcell #ad - 10gram Tube. Continuous service temperature range from -55 to 150°C -67 to +302°F. Appearance Silver, Cure Type Heat cure. When the temperature rises to the action temperature, the transmission contacts act quickly, the square sheet jumps suddenly, and the circuit is disconnected. Mechanical properties hardness, shore D 83, Pot Life 6 months At 25 °C 9 months refrigerated.

Specification : product name : ksd9700 thermostatModel: KSD9700Action Temperature : 45℃Action Type: N. O normal openpower : 250v 5apin type : 2 WiresWire Length : 70mm/2. 76inchmain body material : metallife : 100, 000 times Package Content :2 x KSD9700 Thermostat Description :1. Normally open: the original state of temperature control switch contact is open, and close when the temperature sensing exceeds the rated temperature.

uxcell KSD9700 Thermostat, 45℃ Normally Open Temperature Switch Thermal Switch, N.O 5A Metal Bimetal Temperature Controller 2pcs #ad - 2. Features : ksd9700 temperature controller has the characteristics of small size, accurate temperature control, quick action, large current control and long service life.3. Working principle : KSD9700 uses square bimetal sheet as temperature sensor. Such as electric motors, heating pads, transformers, jacket, Fluorescent Ballasts, OA-Machines Diy carbon heater tape for vest, insoles, Solenoids, gloves.

Electrical resistivity: 0007 Ω·cm, thermal conductivity: 1.

#ad



0.3ML Silver Conductive Wire Glue Paste for Electronics Repair by omyBigDeal

#ad
omyBigDeal BANGXECT26 #ad - High quality ultra flexible soft Silicone Rubber Copper Wire!Super Low Impedance, Highly Efficient! You can also find such dryer at our electrical tools category :   banggood wanna bring you everything you want- really ! Package included : 1 x Silver Conductive Paste 03ml details pictures : Diy carbon heater tape for vest, insoles, jacket, gloves.

Electrical resistivity: 0007 Ω·cm, thermal conductivity: 1. 4 w/m·K. If you want it drying rapidly- blow it with a dryer for 5 - 10 minutes will be OK. Perfect for led GPU Chipset Heatsink. Description : 03ml silver conductive wire glue paste for electronics Repair Applications It's widely used in home supplies- For example refrigerator- drinking machine- electromagnetic oven and electronic kettles etc.

0.3ML Silver Conductive Wire Glue Paste for Electronics Repair by omyBigDeal #ad - Electrical items For example power- inventor- relay and SCR etc. Cpu in computer- led display- lcd display- optical fiber communication equipment- controller- heat sink and LED etc. Sheet resistivity 10-12 m?/sq, Lap shear strength 2000 Lb/in2. High strand count copper core, 22 awg silicone stranded wire has 60 strands 0

08 mm tinned copper wire, the copper strands are tinned, protecting them from corrosion and making it easier to solder.

#ad



SACKORANGE Plastic Battery Storage Case Box Holder for 2 X 18650 with 6" Wire Leads,5 pack

#ad
SACKORANGE 6543877304 #ad - Sheet resistivity 10-12 m?/sq, Lap shear strength 2000 Lb/in2. High quality ultra flexible soft Silicone Rubber Copper Wire!Super Low Impedance, Highly Efficient! Battery type: 5 pcs 18650 Case Holder together. Two-part silver-filled epoxy adhesive with good conductivity and faster working time than MG Chemicals 8331S adhesive to bond electronic devices, form conductivity seals, and cold solder heat-sensitive materials.

Stores and ships at room temperature, no freezing or dry ice required. Features : ksd9700 temperature controller has the characteristics of small size, quick action, accurate temperature control, large current control and long service life. Wide used in home appliance's motor and electrical equipment, such as air Conditioner motor, thermal appliances, transformer, etc.

SACKORANGE Plastic Battery Storage Case Box Holder for 2 X 18650 with 6" Wire Leads,5 pack #ad - New generic plastic battery storage Case Box Holder for 2 x 18650 Black with 6" Wire Leads. Cure time 07 hours at 200 °c, 1. 5 hours at 180 °C, 2. 5 hours at 160 °C. Provides work time of 10 minutes and has full cure time of 5 hours at 77 degrees F. Easy 1:1 mix ratio.

#ad



AC Infinity AXIAL LS1238, Quiet Muffin Fan, 120V AC 120mm x 38mm Low Speed, for DIY Cooling Ventilation Exhaust Projects

#ad
AC Infinity LS1238A-X #ad - Product description The heavy duty axial fan kit is designed for custom projects and as a replacement fan. Diy carbon heater tape for vest, insoles, jacket, gloves. Gennel g109. Popular uses include theater cabinets, woodstove heaters, amplifiers, kegerators, room to room doorways, and more. Two-part silver-filled epoxy adhesive with good conductivity and faster working time than MG Chemicals 8331S adhesive to bond electronic devices, form conductivity seals, and cold solder heat-sensitive materials.

Diy carbon heater tape for vest, insoles, jacket, gloves. Electrical resistivity: 0007 Ω·cm, thermal conductivity: 1. 4 w/m·K. High quality ultra flexible soft Silicone Rubber Copper Wire!Super Low Impedance, Highly Efficient! Because this is a standard industrial size fan, it can be used to replace fans found in various electronics and machinery.

AC Infinity AXIAL LS1238, Quiet Muffin Fan, 120V AC 120mm x 38mm Low Speed, for DIY Cooling Ventilation Exhaust Projects #ad - Heat cure is recommended to get the best possible conductivity. Features : ksd9700 temperature controller has the characteristics of small size, accurate temperature control, quick action, large current control and long service life. Wide used in home appliance's motor and electrical equipment, such as air Conditioner motor, transformer, thermal appliances, etc.

New generic plastic battery storage Case Box Holder for 2 x 18650 Black with 6" Wire Leads.

#ad